• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why is My Car Ignition Locked?

There are a variety of reasons your ignition may be stuck. One reason is that the key is dirty or has a damaged wafer in it. This can be corrected by sliding the key into and out of the cylinder a few times.

The pins of the lock cylinder can also be stuck. You can tap the cylinder lightly using a small tack hammer.

Check the Battery

The shifter switch on the transmission may be malfunctioning if the car is in Park neutral, or doesn't start when the key is switched on. You can fix this by moving the gear shifter upwards or down to put the car into the correct gear.

If the car doesn't turn, the issue could be due to the neutral safety cable, or the shifter in the transmission. They can be fixed by a mechanic or by a local locksmith for cars.

It is also possible that the ignition cylinder has worn out. Over time, the ignition as well as the key can wear out, which causes them to become difficult to remove or insert. A lubricant, such as silicon lock lubricant can solve this issue by allowing the wafers to slide into the place.

The lint in your pocket and the adhesive from the tape that holds packages together can build up on the key, preventing it from being able to slide into the ignition. To solve this problem, you can try cleaning the key with the help of a cloth or a cleaner, like Triflow. You may also try a spare key in order to determine if the problem is the ignition or the key.

When the key is in the ignition, you can tap it using a a small piece of hammer. This can cause a slight vibration, which may cause enough vibration to loosen the wafers inside the ignition and let them slide into the right position. You must be cautious not to damage either the ignition cylinder, or the key.

If none of the suggestions above works, you must contact a locksmith to test the issue. It could be that the key is broken inside the ignition key replacement cost or it could be the time to replace the entire thing. A locksmith can make an alternative key if the issue is with the key. If the ignition cylinder is the problem, you will need to take your vehicle to a repair shop in order for it to be replaced. Fortunately, these issues are typically very simple to solve.

Check the steering wheel

A simple problem that can prevent the ignition from turning is the steering wheel being locked. It can happen if drivers accidentally engage the steering wheel as they exit or get into the vehicle. This is typically caused by yanking the wheel and resting it against their body. It could also happen if a passenger in the back seat is unable to stop it when they get out of the car.

Luckily, this is an easy fix and doesn't require a trip a mechanic or a locksmith. First, check that the gear shift is either in neutral or Park. If it isn't, simply push or pull the shifter until it moves into one of these positions. It's also important to press the brake button or activate the handbrake before you attempt to turn the key.

If the wheel is not locked, a quick examination of the steering column should determine if the key is engaged with the lock cylinder. A small "Lock' label is usually located in the lower area of the ignition circle. You can easily disengage this by gently jiggling or pulling the keys with moderate force. It is crucial not to apply too much pressure, as it could damage the key, or even break a wafer within the lock cylinder.

A spare key can also be used to disengage the lock. This could mean that the key is worn and is no longer able to engage the wafers in the lock cylinder. A professional from Karl Chevrolet Webster City can create a new key in the event that this is the case.

If the new key still isn't engaging, a quick spray of penetrating oil can assist. Apply a small amount around the ignition, and the keyhole that you have inserted, and then jiggle or tap it lightly until it begins to work. If this isn't working, you'll probably need to visit an expert at your local dealership for cars. They'll be able give you a new key and replace the ignition cylinder if necessary.

Check the Key

It could be that your key may be damaged if it doesn't turn in the ignition. You can remove any foreign material (lint from packing tape or adhesive) from the key. You could also try alcohol on the key or Goo Gone to see if it can help.

It's possible that the lock pins inside aren't working properly when you insert the key. If you have an extra key to test, try putting it into the ignition and gently removing it. This should allow you to be able to feel and hear if internal lock pins move, as they should. If not, you could apply lubrication to the pins using graphite powder. You can buy graphite in small tubes that can be squirted directly into the keyhole. This will allow the pins to slide into place when you insert the key, and keep them from becoming stuck.

It could be that your key has become damaged or worn out and isn't able to connect with the pins inside the ignition cylinder. This could cause the cylinder to stop to turn, preventing you from starting your vehicle. If this is the case you'll need take your vehicle to repair or locksmith shop for assistance.

If you can turn your car using an extra key, and you've ruled out any issues with the battery or steering wheel, it is possible that the lost ignition key cylinder has worn out. You can try to loosen the lock using the blunt screwdriver or handle of a small hammer. Do not use the head. Sometimes, gently tapping the cylinder will loosen it and allow you to turn the key of your car ignition lock (see more). If this doesn't work will happen, you'll have to get the lock cylinder replaced by does a new ignition switch require a new key mechanic.

Check the Ignition Socket

The ignition socket is the place your key slides into and out of place when inserted. It is often covered in debris or is a result of regular wear and tear. You can squirt some silicon lock lubricant in the ignition.

You can also employ a small hammer and gently tap the interior of the ignition cylinder, in an effort to loosen or reset the pins which may be out of alignment. Be cautious not to overdo it, or you could cause serious damage to the ignition switch.

Before you do this, ensure that the car's gearbox is set to neutral or park. Many newer cars come with an electronic system that locks the steering wheel if it is not in neutral or in park. This can prevent the ignition key from being turned.

If you have done all of this but cannot get your key to turn it is likely that the housing of your ignition cylinder is in need of replacement. Different vehicles have different methods of replacing the ignition cylinder, therefore it is crucial to follow the correct steps.

Generally, this involves removal of the plastic cover which is over the steering column and ignition assembly. To remove it, you'll need to first adjust the tilt-wheel to the lowest position and then remove any fasteners holding it in place.

After removing the cover you'll need to take off the old ignition cylinder from the steering column. It is then important to compare the new one that you bought with the original one to ensure that they're the same. After this is completed, you can install the new ignition cylinder the same manner as the previous one.

It is possible that despite our best efforts, the ignition may become damaged and need to be replaced. If this happens, it's recommended that you contact a Tempe Locksmith for assistance. A locksmith will be able to assist you in choosing the appropriate replacement and then install it correctly to ensure that your car can be started again.