• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat 500x key 500 Key Fob Won't Work

A key fob from fiat 500x key 500 allows you to easily open doors and start your car. However, there are numerous reasons the fob could stop working. This could be due to a dead coin battery water damage, receiver module issues, and interference.

This listing is for a NEW replacement fiat punto locked keys in car Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). It includes trunk, lock and unlock buttons.

Dead Coin Battery

The most common reason your 500 key fob doesn't function is due to the battery is dead. Modern fiat multipla key fobs operate with a restricted operating range, and should be within only a few feet from the vehicle to function. If you are far from your vehicle and press the keyfob button, it will not respond and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one from a reputable brand like Panasonic Duracell or Energizer. You can typically find them in your local hardware store, or online.

You can test the battery in the coin-cell by pressing the buttons while standing close to your fiat 500 key fob replacement 500 key cover uk - look what i found - 500. The parking lights should flash and the key fob will operate the lock and unlock switch.

If your fob's key isn't working even after replacing the battery, there could be water damage that is preventing it from interacting with the module in your vehicle. Water damage can occur in many ways, including simply splashing or submerging the key fob in saltwater at the beach. If you suspect your fob has been exposed to water, put it in a dry rice bag to pull the moisture back out. If this does not work, you'll need to have the fob reset by an auto locksmith or dealer.

Water Damage

The fob does have rubber seals to keep water out of the electronic chip inside and out of the ocean or washing it in a machine can cause water damage. Saltwater is especially dangerous to the fob's circuit board which causes it to short out and eventually die. It's not the best idea to get the fob wet, but don't give it up if you accidentally drop it in water, or fail to remove it from your pocket.

Remove the battery first. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Then check the fob to check if it functions. If the key does not function then it might need to be programmed again. This is usually done by an auto locksmith or dealer.

If the key is newer and was not programmed to your car It is likely that it needs to be replaced completely. A professional locksmith for automotive can carry out this simple task. The locksmith will need to cut the key to match the ignition of your vehicle. They will also need to reprogram the fob to the car's system. It's a simple and cost-effective process which can be completed on the same day.

Receiver Module Issues

One of the main reasons your 500 key fob might stop functioning is that it's out of range. The remote's range is of 30 feet, which means should you be too far from your vehicle it won't respond to your commands. It is possible to solve this problem by moving the remote closer to your vehicle until it responds.

If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and the fob won't work It could be because of an internal circuit board issue. In most cases, reprogramming the fob will solve the problem. You can find the instructions on how to do this for most vehicles by searching YouTube or checking out the owner's manual.

You may have to replace the metal retaining clips that keep the coin battery in place. If they loose tension, it can prevent your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob may be out of connection with your vehicle as a result of hardware or software problems. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances they might need to reinstall the software on your body control module too.

Interference

Interference can also cause the key fob to be unable to receive or transmit the signal. This could happen if the key fob is close to the radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. The key fob may not work due to a poor connection to the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to resolve it (e.g. replacing batteries, reprogramming or using the spare key fob, you might have a malfunctioning receiver module on your 500. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all on-board systems in your 500, including the key fob. Disconnect the 12 volt battery for approximately 15 minutes by taking off the negative cable first then the positive cable. Reconnect the battery. This will eliminate any residual electricity and restart the car's computer system, which can help get your key fob working again. If the issue continues, you should speak with an expert technician. They will be able to identify the root of any issues.