• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a 2011 kia soul key fob programming Sportage Replacement Key

For a variety of Kia models the key comes with a keyless entry system built-in. This key typically resembles a remote control and can be exchanged with a new one from an Kia dealer or locksmith.

Key fobs might stop working due to various reasons, such as the battery of the coin is dead, worn buttons signal interference, water damage and a damaged receiver module. Here are some helpful tips on how to get your kia sportage replacement key (Click In this article) to work again.

How to replace a remote key or a smartkey?

It doesn't matter if your lost kia key comes with an intelligent key, remote key push to start key, or a regular non-transponder steel key The battery inside these keys will eventually require replacement. This is particularly relevant if your car displays a message indicating that the remote or smart key has a low battery.

It's a simple procedure. In order to replace the battery of the key fob remove the mechanical key from the slit in the back of the key fob and lift the cover. Inside the key fob will be the small screw that holds the battery in place. By using a small screwdriver remove the screw and pull out the old battery. Install the new battery and then close the slit on the key fob.

When the key fob is equipped with an updated battery, test it by pressing the lock and unlock buttons. You're in good shape when the doors lock or unlock as you expect. You can now use Kia's hands-free lock/unlock function whenever your fingers get chilly or you have to go on errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a programing machine, which is only available to the automotive locksmith or dealer. Other keys (non transponder metal keys) are not required for programming. If your key has to be programmed, you must be aware of the key code number stamped on the tag that identifies the key and keep the number in a secure place.

How do you replace the battery?

If your kia flip key broken key fob is not responding to pressing the lock or unlock button on the fob, it is a clear indication that the battery needs to be replaced. A weak battery could cause other issues, such as the check engine light flashing or the engine not running properly. Fortunately, replacing the key fob battery is a relatively simple DIY task that requires only some basic tools.

Make sure you turn off your vehicle and close all doors prior to starting. Find the small metal or plastic piece on the bottom of the key fob. Move it until the key comes out. The key can be inserted into the driver door handle to unlock your car.

To replace the battery in the key fob, take off the cover on the rear. Use a plastic pry tool to loosen up the latch that holds the black negative cable. Take the old battery out, and then orient the replacement battery to ensure its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or bending the contacts of the metal.

Once the new battery has been installed then turn the key fob off and then turn it on in the ignition for a few times until the door locks. You can then test your Kia's keys fob once more to ensure it's functioning properly.

How can you replace the smart key?

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The difference is that the smart key has the small blade of a key tucked inside it, while the standard fob isn't equipped with. Both kinds of key fobs contain an internal battery which eventually needs to be replaced. Luckily, this is quite simple and takes only two minutes.

Before you start before you begin, make sure that you are on a level surface with good lighting and that your Kia is not on. Remember that the fob contains tiny parts that could be thrown off in the event of a mishap.

The first step is to find the small release button on the back of the lower part of the fob. It's either a circular button or rectangular slot. After pressing this button button, the mechanical blade will pop out and you can then open the key fob.

Once the key fob is open, remove the battery that was in it. The new battery is a CR-2032 that can be bought online or from your local auto parts store. Once you're done with the battery, you should be able to lock, unlock and start your vehicle with your key fob, even if your engine isn't running!

How to replace a mechanical key

The Kia keyfob is a great convenience, allowing us to lock or unlock our car by pressing the button. Like any device like a key fob, the Kia can have issues at times. Luckily, there are methods to solve these issues and keep our key fobs in good condition for the long term.

A low or dead battery is one of the most frequently encountered issues. This could cause your device to stop working or work intermittently. If this is the case, replace the battery with a new one.

If this isn't enough to resolve the issue, try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to scratch any internal components or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to check that it's functioning properly. If the device isn't working, contact a locksmith or dealer to help solve the problem. Make sure they make you an emergency key that can work for all trunk and door cylinders, to prevent lockouts in the future.